316L不锈钢金属间相固溶过程中的微结构表征

利用扫描电镜、X射线衍射仪和电子背散射衍射仪等设备研究了热轧态316L不锈钢金属间相(σ相和χ相)在固溶过程中的微结构演变规律,同时,利用高温激光共聚焦显微镜对金属间相回溶的全过程进行了原位在线观察,确定了最佳固溶温度。结果表明,固溶过程中发生了γ+σ+χ→γ+σ+χ+α/FeCr→γ+α/FeCr的相变过程。金属间相的回溶从1033.1℃开始到1149.5℃结束,回溶时间为21s,消除金属间相的最佳固溶温度约为1150℃。固溶处理前,基体中分布的带状组织形态不规则,χ相和σ相的面积比分别为0.46%和0.94%;固溶处理后,带状组织形态一致,主要分布铁素体和FeCr相,而χ相和σ相不可见。     

A Study on Dual-Load-Zone Model of Overlying Strata and Evolution Law of Mining Stress

The changeable structure and movement law of overlying strata are the main contributor to the change of mining stress. Starting from the relevant theory of key stratum and particularly based on the theory of mine ground pressure and strata control, this research proposed a new solution to mining stress problems by establishing a dual-load-zone stratum structural model. Elastic foundation beam theory was used to solve the stress of overlying strata of the dual-load-zones with superposition method, which revised the traditional calculation method of mining stress. The abnormal increase of lead abutment pressure in the mining area was explained effectively, through which the evolution law of mining stress in the case of hard rock was obtained. The results indicate that mining stress experiences a drastic change within the range of 50 m ahead of the coal wall due to the collapse of main roof; under the influence of main key stratum and inferior key strata, the influence range of lead abutment pressure is extended up to approximately 120 m in the working face; this remarkable increase can be attributed to the excessive length of sagging zone. Results from both the dual-load-zone model experiment and field measurement demonstrate high consistency. The model can predict the influence range of abutment pressure effectively and thus guide the safety production of mining.     

吐哈盆地葡北地区“两宽一高”地震勘探技术及应用效果

吐哈盆地台北凹陷圈闭落实的准确度和储层分布预测的精度一直是制约该区油气发现的关键因素。通过可控震源“两宽一高”地震采集、OVT域时间偏移、地质导向深度偏移初始模型建立及各向异性深度偏移迭代处理，在地震资料的信噪比、频带宽度和分辨率等方面明显提高的基础上，以高精度层序地层学为指导，基于高分辨率地震资料与钻井、测井资料的综合分析，识别出侏罗系6个三级层序，在三级层序格架内将研究区七克台组底部和三间房组顶部砂体识别为两个连续上升半旋回四级层序；通过构造几何属性分析及精细构造分析，揭示了本区“四带、两凹”的构造格局及形成机制；以宽频带多种反演技术为手段，对含油气层段的七克台组和三间房组砂体分布进行了预测；在综合构造分析、储层分析和油藏成藏规律分析的基础上，提出本区油气沿构造带脊线聚集，断裂系统是油气运移的优势路径，七克台组、三间房组储层在葡北构造带发育，向玉果构造带和胜北次凹减薄尖灭，葡北构造带与玉果构造带结合部位的，具有鼻状构造背景的岩性圈闭是获得油气突破的有利地区。     

耐蚀合金中TiN析出机制

摘要：TiN颗粒尺寸及其分布对耐蚀合金性能有明显的影响，因此有必要对TiN在铸坯中的分布及其析出行为进行研究。采用扫描电镜(SEM)、金相显微镜（OM）观察了TiN夹杂物在铸坯中的分布、尺寸及其形貌；基于热力学和动力学理论分析了耐蚀合金铸坯中TiN夹杂物的析出时机及其尺寸，结合试验结果和理论计算明确了TiN夹杂物在凝固后铸坯中的位置和尺寸与析出时机的关系，为控制TiN夹杂物提供理论指导。结果表明，冶炼过程中析出的TiN夹杂物尺寸较大，在凝固过程中被枝晶吞没，位于铸坯枝晶内和等轴晶内；微观偏析计算结果表明，在凝固分数为0.55时，TiN开始析出，最开始析出TiN夹杂物的逐渐长大，长大后的TiN易于被二次枝晶吞没，最终位于铸坯中的枝晶间和等轴晶内，后期析出的TiN则在枝晶间和等轴晶间。固相中析出的TiN夹杂物长大较慢，尺寸细小，最终位于奥氏体晶界。     

Development of Biarylalkyl Carboxylic Acid Amides with Improved Anti-schistosomal Activity

The parasitic disease schistosomiasis is the cause of more than 200 000 human deaths per year. Although the disease is treatable, there is one major shortcoming: praziquantel has been the only drug used to combat these parasites since 1977. The risk of the emergence of resistant schistosomes is known to be increasing, as a reduced sensitivity of these parasites toward praziquantel has been observed. We developed a new class of substances, which are derived from inhibitors of human aldose reductase, and which showed promising activity against Schistosoma mansoni couples in vitro. Further optimisation of the compounds led to an increase in anti-schistosomal activity with observed phenotypes such as reduced egg production, vitality, and motility as well as tegumental damage and gut dilatation. Here, we performed structure–activity relationship studies on the carboxylic acid moiety of biarylalkyl carboxylic acids. Out of 82 carboxylic acid amides, we identified 10 compounds that are active against S. mansoni at 25 μm . The best five compounds showed an anti-schistosomal activity up to 10 μm and induced severe phenotypes. Cytotoxicity tests in human cell lines showed that two derivatives had no cytotoxicity at 50 or 100 μm . These compounds are promising candidates for further optimisation toward the new anti-schistosomal agents.     

Digital hysteresis sliding mode control for interleaved DC–DC converters

This paper presents a digital constant frequency sliding mode control (SMC) law for interleaved DC–DC converters. Constant switching frequency and interleaving are achieved by dynamically adjusting the hysteresis of the control signals generating comparators. The interleaving method neither imposes constraints on the number of required phases to obtain a specific output voltage nor uses quasi-SMC. Hence, the control scheme achieves high flexibility, robustness, and performance. Furthermore, a sliding mode observer (SMO) for reconstructing the inductor currents is proposed. Experimental results for a two-phase buck converter are reported. The control concept accomplishes an improved dynamic performance in comparison with quasi-SMC.     

Poly(L-lysine)-poly(ethylene glycol) layers with different structure and their influence on silica suspension stability

The effects of the structure of di- and triblock copolymers of poly(L-lysine) – LYS with poly(ethylene glycol) – PEG as well as the length of nonionic fragment in the LYS-PEG macromolecule on the copolymer chains conformation in the adsorption layer formed on the colloidal silica (SiO2) surface were examined. Spectrophotometry and turbidimetry were applied for the determination of copolymer adsorbed amounts and stability coefficients of silica aqueous suspensions. The electrokinetic parameters such as solid surface charge density and zeta potential were also estimated. The adsorption of LYS-PEG was proved to be the highest at pH 10 whereas the lowest adsorption on the solid surface was found for the triblock copolymer with long fragments of LYS at the same pH value.     

径向弹簧蓄能密封结构最大接触应力的有限元分析

为研究径向弹簧蓄能密封结构的密封特性，针对典型径向弹簧蓄能密封结构，分析其密封机制以及O形弯曲金属螺旋弹簧的弹性特性；采用ANSYS有限元分析软件，建立典型弹簧蓄能密封结构的非线性有限元分析模型，对弹簧蓄能密封圈在不同压缩率、不同介质压力下的接触应力进行分析，研究在多种工况下最大接触应力的变化情况。结果表明：压缩率保持不变时，最大接触应力随着介质压力的增大而增大；介质压力保持不变时，随着压缩率的增大，最大接触应力先增大再减小。对压缩率、介质压力与最大接触应力的关系进行曲线拟合，可用于指导弹簧蓄能密封结构的精确设计。     

基于多视图立体视觉的沙堆三维尺寸测量研究

利用从运动中恢复结构方法(SFM),提出了一种基于多视图立体视觉的沙堆三维重建及三维尺寸测量方法。首先根据SFM方法的求解不稳定特点,结合光束平差法对SFM求解过程进行分析及优化;其次针对SFM重建结果为稀疏点云的问题,利用基于面片的稠密重建算法重新生成稠密的三维点云,再利用泊松算法对密集点云进行三维曲面重建;最后获得模型的三维尺寸信息。对某建筑工地的沙堆进行了三维尺寸的测量实验,实验结果验证了该方法的有效及可行性,提高了重建能力及精度,同时考虑了目标实际测量误差与重建误差,能够满足实际智能测量的应用需求。     

热处理对挤压态Mg-6Gd-5Y-1Zn合金组织与性能的影响

通过对Mg-6Gd-5Y-1Zn(质量分数,%)合金在固溶和时效处理状态下显微组织和力学性能的研究发现,α-Mg基体、沿挤压方向分布的条状18R-LPSO相、少量的Mg₂₄(GdYZn)₅ 相以及细层片状的14H-LPSO相构成了挤压态合金的组成相。挤压态合金经固溶(T4)处理后,一部分18R-LPSO相溶入基体,并且基体中的14H-LPSO相伸长同时粗化。挤压态合金经过固溶加时效(T6)处理后,大量β′相从α-Mg基体中析出。T6态合金的室温力学性能最好,其屈服强度、抗拉强度及伸长率分别为272 MPa、406 MPa和6.1%。β′相沉淀也发生在挤压态合金的直接人工时效(T5)处理过程,但相比于T6处理,14H-LPSO相和β′相在基体中的体积分数均偏低。